EXPLORING PLUMBING FUNDAMENTALS WHEN YOU INSTALL A BATHTUB

Exploring Plumbing Fundamentals When You Install a Bathtub

Exploring Plumbing Fundamentals When You Install a Bathtub

Blog Article

Call

Have you been searching for help and advice about Installing A Bathtub?


How to Install a Bathtub
Mounting a tub isn't precisely brain surgery, but it does require solid plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old tub with a new one is also a moderately tough project. If the old bathtub is conveniently easily accessible, the task can relocate rapidly; if you need to open up a wall surface to remove the old bathtub and also position the brand-new bathtub, the job is much harder. In either case, the job is within a home handyman's skills, although you will need an assistant to move out the old bathtub as well as embeded in the brand-new one. Ensure you have certified on your own for the task as well as are comfortable trying it. Rather than hiring a service provider to take over a halfway-completed project, it is better to consider utilizing one before you start. Chances are you might require a professional plumber to make tube links.
This post will certainly aid you set up a brand-new bath tub in your restroom if you have actually already purchased a brand-new bathtub and also don't require to alter the setup of your previous water system pipelines.
Your devices as well as product list ought to make up the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you should do is separate the water system. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of eliminating the existing faucets can be fairly troublesome due to the limited accessibility that is frequently the instance.
    Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a towel ready for the continuing to be water that will come from the pipelines. Once the supply pipelines have actually been gotten rid of, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
    Before going on to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the new faucets to fit.

    Fitting New Taps


    If the tails of the brand-new taps are plastic, after that you will certainly require a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end gives a connection to the current supply pipelines.
    If you need to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
    Next off, place the faucet in the installing opening in the bath/basin guaranteeing that the washers remain in location in between the tap and also the sink. Safeguard the faucet in position with the producer offered backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The previous type should be attached to the faucet ends first, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.

    Mounting the Bath tub


    Using the two wooden boards under its feet, put the bathtub in the needed placement. The wood boards are handy in uniformly spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny points.
    The next goal is to ensure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the bath tub till the spirit level reviews level.
    To set up taps, fit the bottom of the outermost versatile faucet adapter to the suitable supply pipe by making a compression join; then do the exact same for the other tap.
    Switch on the water system and examine all joints and also new pipework for leakages and tighten them if needed. Fill the tub and additionally check the overflow outlet as well as the typical outlet for leakages.
    Finally, deal with the bathroom paneling as explained in the producer's user's manual. Tiling as well as sealing around the bathtub needs to wait up until the tub has actually been utilized a minimum of once as this will settle it into its final position.

    Getting ready for the Installment


    Firstly, the sustaining framework provided with the bath ought to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is necessary to ensure that if the tap includes a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps system to stop pressure on the bathtub.
    Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use all of the supplied washers.
    Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its final placement.

    Tiling Around the Bath tub


    In the location where the bath fulfills the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a stiff seal, creating the water to penetrate the wall surface in between the bath and also the tiling, resulting in difficulties with wetness and possible leakages to the ceiling listed below.
    You can choose from a selection of coloured sealants to assimilate your components as well as installations. They are offered in tubes as well as cartridges, and can securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked paper or soft rope. Keep in mind to always load the bathtub with water before securing, to enable the motion experienced when the tub remains in usage. The sealant can split relatively early if you do not consider this activity before securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly available on the marketplace. It is a good idea to fit the ceramic tiles utilizing waterproof or water-proof sticky as well as cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub Yourself

    I hope you enjoyed reading our section about How to Install a Bathtub. Thanks a lot for taking a few minutes to read our short article. Are you aware of another individual who is in to the niche? Do not hesitate to share it. Thanks a bunch for your time. Visit again soon.


    Fast response, call now!

    Report this page